Logo G4energy

Aluminium dock plates

for loading and unloading goods at docks and loading bays

Dock plates for warehouses and logistics centres

Our aluminium dock plates are loading dock equipment: they are fixed to the edge of the loading bay and bridge the height difference and gap between the warehouse floor and the bed of trucks and vans. They let pallet trucks and handling equipment carrying palletised goods cross safely during everyday loading and unloading.

They are not portable ramps for loading motorbikes, quads or small vehicles onto a trailer: they are built to work every day in logistics environments, with the capacity and safety devices that goods traffic requires.

What are aluminium dock plates?

Where there is a dock or loading bay, aluminium dock plates let a single operator handle loading and unloading. The plates are fixed with strong steel or aluminium brackets that allow the plate to be tilted or slid along the dock.

Manual aluminium dock plates have a gas spring that assists lifting, so one operator can handle them by hand.

pedana in alluminio manuale

Our aluminium dock plate solutions

Safety locks prevent accidental opening when the plate is at rest, and pedestrian fall-protection barriers can be fitted to make the work area much safer for the operator.

Manual aluminium dock plates are available in sliding and hinged versions; both are strong, safe and cost-effective ways to bridge the dock and the vehicle.

The recommended maximum working gradient (as required by current standards), up or down, is 12.5%.

Two versions: hinged and sliding

Both have safety locks that prevent accidental opening when the plate is at rest, and can be completed with pedestrian fall-protection barriers along the dock edge.

Hinged dock plate

Hinged to the dock edge. At rest it stays upright; for loading, the operator lowers it onto the vehicle bed, helped by a gas spring that reduces the effort. The simplest solution when every door has its own plate.

Sliding dock plate

Slides along a rail fixed to the dock edge. It moves in front of the vehicle’s rear door, so one plate can serve several positions and adapt to where the truck stops.

How to choose the right dock plate

We only need a few details to size the plate, and you can send them using the form at the bottom of the page:

  1. Height difference between dock and vehicle bed, for the lowest and highest vehicles you serve. This sets the length: the recommended working gradient should not exceed 12.5%, so, for example, a 15 cm difference needs a plate of about 1.2 m.
  2. Handling equipment and load weight: manual or electric pallet truck, maximum pallet weight. These set the capacity.
  3. Clear width, based on the width of the pallets and the equipment.
  4. Type of dock: concrete or steel structure, to choose the fixing brackets.
  5. Number of doors to serve: one hinged plate per door or one sliding plate for several positions.

Aluminium dock plate FAQs

No. G4 Energy dock plates are fixed loading dock equipment for logistics: they are installed at the loading bay for pallet trucks and goods-handling equipment. Loading motorbikes or quads onto a trailer needs portable ramps, which are a different product.

A manual aluminium plate is economical, needs no electrical supply and suits small height differences. For larger differences, heavy traffic or heavy loads, an electrohydraulic dock leveller is the better choice. We will help you decide based on the vehicles you serve.

The recommended working gradient, up or down, is 12.5% at most. That is why the plate length is chosen according to the height difference between the dock and the vehicle bed.

Yes. The plate is fixed to the dock edge with steel or aluminium brackets, on concrete docks or steel structures.

The minimum and maximum height difference between the dock and the vehicle bed, the equipment you use and the load weights, the door width and, if possible, a few photos of the dock.

Aluminium dock plate installations

The photos show two applications: hinged dock plates installed on a steel structure with guardrails under a canopy, and a plate mounted on the edge of a concrete dock.

In these photos the plates are raised in the upright rest position.

Pedane ribaltabili in alluminio su struttura metallica sotto pensilina
Hinged aluminium dock plates on a steel structure with guardrails, under a canopy.
Vista laterale pedane in alluminio con parapetti
Side view of the same installation, with the plates in the rest position.
Pedana in alluminio G4 sul bordo banchina in posizione di riposo
Aluminium dock plate mounted on the dock edge, upright in the rest position. Installation in progress.

Fill in the form for a free consultation